pgmfi.org

Hacking up Honda's ECU
It is currently Sat Feb 24, 2018 1:36 pm

All times are UTC - 5 hours [ DST ]





Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: New to HomeBrew Chipping
PostPosted: Wed Apr 18, 2012 6:53 am 
Offline

Joined: Tue Feb 01, 2011 7:45 pm
Posts: 4
Hi

I know this seems to be a dead part of the this forum, but i thought i will post here.

Currently been trying to chip my PR3 ecu, but getting constant CEL and Solid ECU
So far tried chipping two with the same result then purchased a PR3 with some bs fuel saver chip but it still gave me the same result.

But anyway im determined to get it going in my b16 CRX

Cheers


Top
 Profile  
Reply with quote  
PostPosted: Wed Apr 18, 2012 12:54 pm 
Offline

Joined: Wed Feb 29, 2012 10:23 am
Posts: 79
Location: Japan
PR3 obd0?
first step to check is ur solder contact.
2nd step is check ur CHIP. make sure its 27C256 if u use 27C512, u need to off set HEX 8000 when burn chip.
3rd check correct rom burn. (u cannot get a OBD1 rom file put in to OBD0 ecu)

i have done many chipping... most is rom issue... like example JDM version have KS board, if u put JDM rom into USDM that dun have KS board without turn off KS in editor, that will make solid cel.

**correct me if im wrong. :D


Top
 Profile  
Reply with quote  
PostPosted: Wed Apr 18, 2012 10:19 pm 
Offline

Joined: Sun Nov 22, 2009 5:42 pm
Posts: 966
Location: Cincinnati, Ohio
There is no obd0 usdm p30 and the usdm obd1 p30 has a knock board. If you have a rom with the knock enabled and a ecu without a knock board it will NOT cause a soild cel, just a knock sensor code.

Make sure the rom you are running is the same obd as the ecu.


Top
 Profile  
Reply with quote  
PostPosted: Thu Apr 19, 2012 8:47 am 
Offline

Joined: Wed Feb 29, 2012 10:23 am
Posts: 79
Location: Japan
sicknastyb17 wrote:
There is no obd0 usdm p30 and the usdm obd1 p30 has a knock board. If you have a rom with the knock enabled and a ecu without a knock board it will NOT cause a soild cel, just a knock sensor code.

Make sure the rom you are running is the same obd as the ecu.


JDM OBD1 P30 have KS board. and USDM P30 have in OBD0 model? from when i know how to chip ECU start until today i never see a P30 with OBD0 model, interested if it have in USDM, mind to snap some pic and mail me? million thanks....


Top
 Profile  
Reply with quote  
PostPosted: Thu Apr 19, 2012 11:08 pm 
Offline

Joined: Sun Nov 22, 2009 5:42 pm
Posts: 966
Location: Cincinnati, Ohio
I meant to type obd0 pr3


Top
 Profile  
Reply with quote  
PostPosted: Tue Apr 24, 2012 2:31 am 
Offline

Joined: Tue Feb 01, 2011 7:45 pm
Posts: 4
Hi Guys!

Thanks for the reply's, i have been checking a couple of the ecu's i have.

Turned out there was a poor soldering on the PW0 ecu i had, that was giving me high resistance, found it and fixed it yesterday.
Installed in the CRX today and went perfect, same with the two chips i had burnt for it. so one down one to go.

But most importantly i can finally start getting in to tuning this car and learn the process :)


Top
 Profile  
Reply with quote  
PostPosted: Sat May 12, 2012 12:20 pm 
Offline

Joined: Wed Feb 29, 2012 10:23 am
Posts: 79
Location: Japan
bboyzell wrote:
Hi Guys!

Thanks for the reply's, i have been checking a couple of the ecu's i have.

Turned out there was a poor soldering on the PW0 ecu i had, that was giving me high resistance, found it and fixed it yesterday.
Installed in the CRX today and went perfect, same with the two chips i had burnt for it. so one down one to go.

But most importantly i can finally start getting in to tuning this car and learn the process :)


good luck. i had experienced once too when 2 months ago... contact failure due to board copper linkage damage. tiny damage and need to use micro scope to find out.... haha... that waste me whole day....


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron


Powered by phpBB® Forum Software © phpBB Group